It is currently Tue Dec 10, 2019 1:46 pm




 Page 3 of 5 [ 71 posts ]  Go to page Previous  1, 2, 3, 4, 5  Next
Author Message
 Post subject: Re: xegs rom basic
PostPosted: Mon May 28, 2012 6:03 am 

Joined: Thu May 03, 2012 3:26 pm
Posts: 31
http://www.ebay.it/itm/New-Secure-Digit ... 2c65850faa

today the adapter sd / ide has arrived.
must the adapter be fed with 12 5?
me where I can withdraw 12 5 in the mother card?
thanks


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Mon May 28, 2012 6:53 am 
User avatar

Joined: Sun Nov 02, 2003 8:15 am
Posts: 1376
Location: netherlands
The adapter in the ebay-link needs 5 volt


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Tue May 29, 2012 7:15 am 

Joined: Thu May 03, 2012 3:26 pm
Posts: 31
me to use connector for pc and to connect 5 v to the yellow thread in sd /ide adapter?

do I also have a cf / ide adapter, if I use this where do I connect 5 v?
thanks excuse me for the trouble :(

in the mother card where I can withdraw 5 v?


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Tue May 29, 2012 12:37 pm 
User avatar

Joined: Sun Nov 02, 2003 8:15 am
Posts: 1376
Location: netherlands
For the IDE-to-CF adapter:
-connect IDE pin 20 to 5 volt.
The adapter (my link to ebay) does not need a power-cable.
5 volt on pin 20 is OK.
Please upload a picture to verify!


On the example PCB from my homepage:
-connection 2 is 5 volt.
-connection 1 is 0 volt.


Your IDE-to-SD needs a power connection.
Look good to your adapter, IDE has no pin 20!


Power connector on PCB
+--- 5 volt
+--- 0 volt
+--- 0 volt (NOT CONNECT)
+--- 12 volt (NOT CONNECT


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Thu May 31, 2012 7:57 am 

Joined: Thu May 03, 2012 3:26 pm
Posts: 31
I have tried adapters on my pc.
I have connected adapters to the power of the pc. must I connect 5v and gnd all adapter,l I use a hookup removed by a pc, where can I withdraw 5 v from the mother sche of the xegs?

graces and excuse me


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Fri Jun 01, 2012 4:35 am 
User avatar

Joined: Sun Nov 02, 2003 8:15 am
Posts: 1376
Location: netherlands
On the example PCB from my homepage:
-connection 2 is 5 volt.
-connection 1 is 0 volt.


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Fri Jun 01, 2012 5:37 am 

Joined: Thu May 03, 2012 3:26 pm
Posts: 31
I have settled on the pcb a cable ide.
the pin 1 are the red thread?


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Sat Jun 02, 2012 2:01 am 
User avatar

Joined: Sun Nov 02, 2003 8:15 am
Posts: 1376
Location: netherlands
pancioalbe wrote:
I have settled on the pcb a cable ide.
the pin 1 are the red thread?


Yes


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Sun Jun 10, 2012 4:34 am 

Joined: Thu May 03, 2012 3:26 pm
Posts: 31
I have finished building the circuit :)

I must now climb on him/it inside xe.

I have a question for you, the pin 1 of my ide goes to the pin 1 of the cpu and the pin 2 of my ide goes to the pin 8 of the cpu but the pin 1 and 2 of my ides go to gnd and 5v?

graces and excuse still me


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Sun Jun 10, 2012 5:30 am 
User avatar

Joined: Sun Nov 02, 2003 8:15 am
Posts: 1376
Location: netherlands
Yes, that is correct.

pin-1 = gnd
pin-8=5 volt

http://www.atarimax.com/jindroush.atari ... sally.html

Later!
Sijmen.


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Sun Jun 10, 2012 6:08 am 

Joined: Thu May 03, 2012 3:26 pm
Posts: 31
I have connected l adapter sd.
I start xegs and on monitor writes no memo pad ( no booted software)

what must I put inside the card sd? .
how must I format it?
thanks


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Sun Jun 10, 2012 7:10 am 
User avatar

Joined: Sun Nov 02, 2003 8:15 am
Posts: 1376
Location: netherlands
Nice it works :-)
Yes, put the SD in and powerup.
Hold START+SELECT+OPTION
Follow the quick-quide.

Did you read the manual?
Firmware 4.7.05 ?

Later,
Sijmen.


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Sun Jun 10, 2012 7:51 am 

Joined: Thu May 03, 2012 3:26 pm
Posts: 31
when I start xe it appears the writings initialize...format make etc and above a black square.
I press The but nothing doesn't happen, I press F it doesn't happen anything.
I have tried sd adapter and cf adapter ,

the keyboard works


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Sun Jun 10, 2012 12:05 pm 
User avatar

Joined: Sun Nov 02, 2003 8:15 am
Posts: 1376
Location: netherlands
From the manual:

QUICK-START (MyDOS):
This is a quick guide how to setup your system with 2 logical drives and image-space. Suitable for the average user working with MyDOS.

· Put the MyDOS disk in drive #1 (Physical drive or sio2pc/Ape).
· Boot your Atari while holding START+SELECT+OPTION.
You should enter the MyIDE_MENU. If the IDE-device is new/unused, there may be garbage on the screen.
· Press I* (init) and wait until it has detected the drive geometry.
*) Hold –shift- for manual CHS input, hold –control- for manual image input, or both.
If the device supports PIO-8 and has enough room, you will be asked to create a FAT32-area **). FAT32 will roughly be 50% of the media.
**) After completion of the init-routine the extra partition is usable on your PC. You need to format the partition on the PC. For SIDE-users selecting FAT32 will automatically reserve half the FAT32-space for APT.
After init the bottom line shows the CHS, Image, PIO-8 values of your device. Please check CHS-values, do a manual CHS input when wrong.
· Press M (Make), <enter> (Drive #), 720 <enter> (Sectors #), S (density). Name: BOOTPART (example)
This is your primary boot partition for system-related software.
There is not a drive-ID attached to it, since we can’t boot from it yet.
· Press M (make), 2 (Drive #), 65535 (Sectors #), D (Density).
Name: MYDOS <enter> (example).
This is your data partition. Use it for non-system files.
[On small drives it's possible that you get less then 65535 sectors. This is the] [space below the area reserved for images. You need this given value to correctly] [configure MyDOS. Alternatively you can increase space by using control-I and add] [blocks of 256 cylinders. This will reduce space for images]
· Press ESC (exit), then Y (save).
This will save and perform a powerup of the Atari.
[It should boot MyDOS from D1:]
· Wait for the DOS menu.
· Press HELP, this will enter the MyIDE-MENU.
· Press C (Change) A (Partition) 1 (Drive #).
[We want to enable D1: on IDE.]
· Press ESC (exit), then Y (save).
[You will safely return to the MyDOS menu.]
· Configure D2: as high capacity. Press O 2 N Y Y 65535(*) enter.
*)enter the correct amount of sector if your partition is not 65535.
If you forgot the value, press HELP to see and ESC/N to return.
· You can disable verify for faster write. Press V, then N.
· Format D1:. Format D2:. Write DOS-files to D1:
[DONE]

For safety reasons, I then protect partition A (D1:), just in case…
(HELP, T, A, ESC, Y)

That’s all. System now is bootable from D1: assigned to IDE.


Offline
 Profile  
 
 Post subject: Re: xegs rom basic
PostPosted: Sun Jun 10, 2012 12:07 pm 
User avatar

Joined: Sun Nov 02, 2003 8:15 am
Posts: 1376
Location: netherlands
And please update to 4.7.05 !


Offline
 Profile  
 
Display posts from previous:  Sort by  
 Page 3 of 5 [ 71 posts ]  Go to page Previous  1, 2, 3, 4, 5  Next


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

cron